Blush

Blush can be defined as a clouded discoloration normally found at gate locations, but they can be found anywhere on the part surface. These visually defective areas have very weak physical properties due to loose molecular structure.

MACHINE
EXCESSIVE INJECTION FILL SPEED
Explanation: The speed and pressure of the melt as it enters the mold determine both density and consistency of melt in packing the mold. If the fill is too fast, the material tends to ``slip'' over the surface and will ``skin'' over before the rest of the material solidifies. The slipped skin area does not faithfully reproduce the mold steel surface, as does the material in other areas, because it has not been packed tightly against the steel.Solution: One solution is to adjust the fill speed rate until the optimum has been achieved. This will help eliminate blushing.

MELT TEMPERATURE TOO HIGH OR TOO LOW
Explanation: Although this may sound contradictory, either condition might cause blushing. If the injection barrel heat is too high, the material will flow too quickly, resulting in slippage of the surface skin, as mentioned above. If the barrel heat is too low, the material may solidify before full packing occurs and the plastic will not be pushed against the mold steel, especially in the gate area because that is the last area to pack.Solution: Melt temperature must be adjusted to the optimum for a specificmaterial and specific product design.

LOW INJECTION PRESSURE
Explanation: The plastic material must be injected into the mold in such a way as to cause proper filling and packing while maintaining consistent solidification of the melt. Injection pressure is one of the main control variables of the machine and must be high enough to pack the plastic molecules against the steel of the mold while the plastic cools. Low pressure will not achieve this packing and the material will appear dull in local areas that do not have enough pressure.Solution: Increasing the injection pressure forces the material against the mold surface, producing a truer finish that replicates the steel finish.

NOZZLE DIAMETER TOO SMALL
Explanation: The nozzle diameter controls the time during which the material fills the mold. If the diameter is too small, the material may begin to solidify before the mold is filled. Then, packing cannot occur because the material is already rigid. Blush will occur because the plastic has not been forced against the steel surface.Solution: Enlarging the nozzle diameter will minimize the condition. The nozzle tip is interchangeable and a tip with the opening the same as, or slightly smaller than, the sprue bushing opening is recommended.

LOW NOZZLE TEMPERATURE
Explanation: A nozzle that has a low temperature will cause the material going through it to cool off too soon and not be allowed to pack out the mold. The non-packed molecules will form blush because they cannot replicate the steel finish.Solution: Increasing the mold temperature will allow the material to flow easier, and for a longer time, thereby packing the mold and replicating the steel finish. Normally, the nozzle temperature should be set the same as, or 10 degrees hotter than, the front zone of the barrel.

MOLD
LOW MOLD TEMPERATURE
Explanation: A low mold temperature may cause the molten material to slow down and solidify before the mold is packed out. This will cause dull areas where the plastic was not forced against the steel finish.Solution: Increasing the mold temperature allows the material to flow farther and pack properly. The material temperature could also be raised to accomplish the same effect.

IMPROPER VENTING
Explanation: Trapped air can cause blushing if the air is trapped in an area that does not compress the air enough to ignite it. The air takes up space where the plastic should be, so the plastic is not forced against the steel finish.Solution: Vent the mold by grinding thin (0.0005''-0.002'') pathways on the shutoff area of the cavity blocks. Vents should take up approximately 30% of the perimeter of the molded part. Add vents in local areas that show blush. Vent the runner, too. Any air that is trapped in the runner will be pushed into the part.

SMALL SPRUE BUSHING DIAMETER
Explanation: A small sprue-bushing diameter will keep the material from packing because the small opening reduces the ability of the plastic to flow far enough to fill the mold. An unpacked mold will cause blushing where the material is not forced against the mold steel.Solution: Size the sprue bushing major diameter so its cross-sectional area is equal to (or greater than) the sum of the cross-sectional area of all the runners leading from it. Then, taper the sprue diameter to match the nozzle. That will ensure proper pressure drop adjustments to pack the mold.

IMPROPER GATE LOCATION
Explanation: If a mold is gated such that the thinnest areas fill first, those areas will begin to solidify before the thicker areas are packed. Blush will form in the thicker areas because there is no pressure left to pack the plastic against the steel surface.Solution: Make sure the gate is located so the thicker sections fill first. The material should flow from thick section to thin section. That ensures equal packing of all areas.

SHARP CORNERS
Explanation: If the product design contains sharp corners, the material tends to slip by those corners without fill them in. The corners are not packed with material and blush occurs due to that non-packing.Solution: Radius all sharp corners, especially in the gate area, as that is the last place to pack. Sharp corners should not be allowed on any molded part.

MATERIAL
EXCESSIVE MOISTURE
Explanation: In some cases, excessive moisture in a melt will accumulate at the gate area. The reason for this is that the gate area is the last place the pressure builds up. Moisture trapped in other areas may be forced into the gate area due to this pressure buildup. The gate area will appear dull due to the moisture that gets screened out. Usually, this type of blush is accompanied by splay.Solution: Dry the material to the supplier's recommendations and make sure it is used within two hours of that drying activity.

OPERATOR
INCONSISTENT PROCESS CYCLE
Explanation: It is possible that the machine operator is the cause of delayed or inconsistent cycles. This will result in excessive residence time of the material in the injection barrel. If such a condition exists, materials may fill at a faster speed and cause slippage as explained earlier. Slippage causes blush.Solution: If possible, run the machine on automatic cycle, using the operator only to interrupt the cycle if an emergency occurs. Use a robot if an ``operator'' is really necessary. And, instruct all employees on the importance of maintaining consistent cycles.